| Effect of tool material properties and cutting conditions on machinability of AISI D6 steel during hard turning M Nayak, R Sehgal Arabian Journal for Science and Engineering 40 (4), 1151-1164, 2015 | 37 | 2015 |
| Mechanical characterization and machinability behavior of annealed AISI D6 cold working steel M Nayak, R Sehgal, RK Sharma Indian Journal of Materials Science 2015, 2015 | 13 | 2015 |
| Investigating Machinability of AISI D2 Tool Steel using CBN Tools during Hard Turning, M Nayak, R Sehgal, K Rajender Materials Today Proceeding 47 (13), 3960-3965, 2021 | 11 | 2021 |
| A Literature Review on Optimization of Input Cutting Parameters for Improved Surface Finish in Turning Process V Jakhara, M Nayakb, N Sharmac | 7 | 2017 |
| Experiment Modeling of Response Parameters and CBN Tool Wear in Continuous and Interrupted Hard Turning of AISI D6 Tool Steel M Nayak, R Sehgal Indian Journal Of Science and Technology 12 (19), 1-16, 2019 | 4 | 2019 |
| Review Of Power Generators Used In Electrical Discharge Machining Process M Nayak, N Seema International Journal of Scientific Research and Review 7 (4), 2019 | | 2019 |
| Hard Turning using Cubic Boron Nitride: A perspective M Nayak International Journal of Scientific Research and Review 7 (4), 2019 | | 2019 |
| REALIZING LOW COST TOOLING FOR RECONDITIONING OF THREAD ROLL M Nayak International Journal of Engineering Applied Sciences and Technology 3 (11 …, 2019 | | 2019 |
| Realization of Low Cost Tooling for Reconditioning of Thread Rolls M Nayak International Journal of Engineering Applied Sciences and Technology 3 (11 …, 2019 | | 2019 |
| An Overview of Value stream mapping and Just in time in Lean manufacturing DMN Kamal Sachdeva, Sudipta Sachdeva, Dr Aks Choudhary ICQPROM 2017, 2017 | | 2017 |
| Some of The Experimental Investigations of Electrical Discharge Machining Process BKBM Nayak ICQPROM 2017, 2017 | | 2017 |
| Predictive Models of Continuous and Interruptive Machining Processes RS Manoj Nayak ICQPROM 2017, 2017 | | 2017 |
| Risks Identification in Supply Chain Management of an Indian Firm - An ANP Approach MN Manish Kumar ICQPROM 2017, 2017 | | 2017 |
| A literature review on optimization of cutting parameters for surface roughness in turning process V Jakhar, M Nayak, N Sharma Int. J. Eng. Res. Dev 4, 2810-2815, 2017 | | 2017 |
| A Literature Review on Optimization of Input Cutting Parameters for Improved Surface Finish in Turning Process Vivek Jakhar, Manoj Nayak International Research Journal of Engineering & Technology 4 (3), 2810-2815, 2017 | | 2017 |
| Experimental Investigation of Cutting Parameters Influence on Surface Roughness in Turning of Alloy Steel ASTM A182, Grade F91 Vivek Jakhar, Manoj Nayak International Journal of Advanced Research in Mechanical Engineering …, 2017 | | 2017 |
| Continuous and Interrupted Hard Turning Using CBN-L Tools at Moderate Cutting Speeds” Rakesh Sehgal, Manoj Nayak & Rajiv Kumar Sharma International Journal of Emerging Technology and Advanced Engineering, 5 (4), 41, 2016 | | 2016 |
| Modeling Motion Control of Robot Arm using Matlab/Simulink M Nayak Proceeding International Conference in Engg. & Technology, College of Engg …, 2012 | | 2012 |
| New Paradigm in Machining Manoj Nayak, Rakesh Sehgal International Journal of Engineering & Technology 4 (1), 31-42, 2012 | | 2012 |
| Role of Tribology in Machining Component and Systems Manoj Nayak, Rakesh Sehgal National Tribology Conference – 2011, 8th – 10th Dec. 2011, IIT-Roorke …, 2011 | | 2011 |
